Nylon Casting

Nylon Casting Nylon Casting



 
Food Approved Product

 


Nylon casting is ideal for manufacturing large sheets, rods or tubes that are not readily available. This unique plastic casting process is also suitable for manufacturing the same plastic component required on a regular basis. At PAR Group we manufacture our own brand of Corromide® cast Nylon 6 in rods, sheets and tubes. We hold tooling for a range of standard sizes and also offer a custom nylon casting service for specific customer requirements. We have ultra-sonic detection equipment and can carry out inspections on castings for voids and porosity upon request. We also offer an in house plastic machining service for all our nylon castings.

Corromide® Grades Available

Grade Property Standard Colour*
CN General purpose engineering grade. Natural
CMF MoS2 filled for improved wear resistance, lower friction and greater heat stability. Black
CHS Heat stabilised to reduce stress build up within the material and increase heat stability. Blue
COF Lubricated with oil for faster speeds and higher loads. Low moisture absorption. Green
CFQ Food approved oil lubricant for food machinery applications. Cream
CMG Lower moisture absorption than CN. Developed for offshore and underwater applications. Yellow
CSL Solid lubricant filled for improved wear resistance and lower friction. Grey

*These are the standard colours used to denote the particular grade of Corromide®. We are able to cast any grade of Corromide® in natural, black, green, yellow, blue, red or purple should your application require it. More colours can also be supplied upon request.

Note: If a specific colour of material is required, please state this in writing at the point of enquiry. Colour tones may vary.

Corromide® is a registered trademark of PAR Group Ltd

Technical Specification:

Technical Data Sheet - Comparison Sheet

Cast Nylon 6 Sheets

Cast Nylon 6 Sheets

We hold tooling for the following sheet sizes. Other sizes can be manufactured upon request.

Sheet Size (mm) Thickness (mm)
2000 x 1000 15, 20, 25, 30, 35, 40, 45, 50, 55, 60, 65, 70, 75, 80
2000 x 1220 15, 20, 25, 30, 35, 40, 45, 50, 60, 70

Cast Nylon 6 Rods

Cast Nylon 6 Rods

We hold tooling for the following rod sizes. Other sizes can be manufactured upon request.

Rod Length (mm) Rod Diameter (mm)
610 70, 75, 80
1000 90, 102, 118, 120, 131, 140, 166, 170, 180, 190, 204, 225, 254

Cast Nylon 6 Tubes

Cast Nylon 6 Tubes

We hold tooling for the following tube sizes. Other sizes can be manufactured upon request.

Inside Diameter (mm) Outside Diameter (mm) Tube Length (mm)
25 50, 52 1000
30 50, 52, 60, 65 1000
35 50, 52, 60, 65, 70, 77 1000
40 50, 52, 60, 65, 70, 77 1000
45 65, 70, 77, 90 1000
50 70, 77, 90, 102 1000
55 90, 115 1000
60 102, 120 1000
65 90, 115, 120, 130, 143 1000
70 102 1000
75 102, 115, 120, 130, 143, 153 1000
80 115 1000
90 120, 130, 143, 153, 170, 180 1000
100 130, 143, 153, 170, 180, 194, 205 1000
115 153, 170 1000
125 170, 180, 194, 205, 245, 254 1000
145 180 1000
150 194, 204, 245, 254 1000
170 194 1000
180 205, 245, 254 1000
200 245, 254 1000

Examples of our Nylon Casting

Plastic Sprockets Timing Screws and Scrolls Rollers, Pulleys and Trunnion Wheels
Plastic Sprockets Timing Screws and Scrolls Rollers, Pulleys and Trunnion Wheels
     
Cast Nylon Component Cast Nylon Hand Wheel  
Cast Nylon Component Cast Nylon Hand Wheel  

Recently Viewed